Steve Promo's Cherry Salad Bowls

 Steve receive a contract to make salad bowls.  He made 14 Cherry Salad Bowls and they look great.

Submitted 22 November 2024.

 

9 November 2024 Club Meeting

This was the last meeting of 2024 and we had a great turn out of members who brought lots of samples of their turnings and some nice bring backs for our raffle.  

Ash outer cut slab.  Steve said you can make some really nice edged bowls from it.

These are some great bring backs that were raffled off during the meeting.  Left is a section of Ash, behind that is a crouch of a tree, to its right is a burl.  Four turnings and a decorative center piece were also brought backs.  

Sam Staffan made the chess set for his son.  All hand made with pieces turned on the lathe and carved.
Other items are decorative segmented pieces.  

More of Sam's great work.

Here is a close up of Sam's segmented turnings.  

More of Sam's ornamental segmented turnings.

Sam brought in some pieces that illustrate how he made the ornamental segment turnings.  
Left is four sections taped together and turned for the inside.   The four sections are turned so the turned outer edges are facing inward and turned for the outside like the second from left.  Next over to the right are the loose sections that would make up the pieces with the inside turned along with some finished pieces.  

The two bows on the left are from Kate and the top three are from Jim Rutledge.

Jim is a master carver and here is a humming bird perched on a stick on the lid of a nicely turned box.   

Here is another wonderful creation from Jim.   A turned bowl made to look like a woven basket with carved feathers in the bottom.  The feathers look so real.  Nice work Jim.

Next to one of Kate's outstanding bowls and another box from Jim with a wonderful bird on the lid.  

Here are two of Kate's fantastic spalted bowls in a natural edge design.  

A beautiful bowl on the left next to a fantastic box.  

Here is a look down the rest of the table loaded with fantastic objects from our members.  

Steve Promo brought in this segmented bowl.  

Here is another of Steve's segmented bowls.  

This a solid wood vase with fantastic wood color. An insert is placed in the vase for a flower.  A real beauty.  

Here are some of Archie Patterson's turnings.  Left is a small mallet.  The bowel on the top was clamped into chuck and the bottom was finished.  However, the furnace came on and the bowl could not expand so it cracked.   Bottom are two domed boxes.  

This is Archie's Orange Agate bowl with a outwardly turned lip and a Ebony wood base.   The finish is buffed CA glue.

In the last issue of Woodturners Magazine there was an article about turning domed boxes with tops reminiscent of the domed buildings of the Middle East and Russia.   After reading the article Archie made these with gold colored hollowed tops and and a dark wood accent piece on the side.  

Here is a nifty pitcher with lid and leather strap handle.  

The photograph does not do justice to these two very large and very beautiful Cherry bowls.  

Placed at the end of the table were these, not to be overlooked, treasures.  Back is a paper towel holder, right is a bowl and left are three biscuit cutters.  

After show and tell Steve Promo talked about making a laser holder for our boring bars.  This was part four of a series where members made the boring bars, a boring bar support and steady rests.  To determine the wall thickness of the turnings a laser can be used to point, say 1/4" from the cutter.  When the laser dot reaches the work's edge you have reached your desired thickness.  In the following movie Jim will explain about using the laser and the making of the laser holder, then he will turn the vertical stand for the laser holder.  Following the movie there are some pictures to further show what was done.  Enjoy.

Do to technical difficulties there is no sound during the turning.  Comments were added to help clarify what was happening in the movie.   

This is the finished laser holder mounted on a boring bar.  The laser is an inexpensive unit from a local hard ware store often used to play with cats.  Jim uses a clothes pin to hold the laser button down to keep the laser on.

This is the top mount bracket with a wing nut to tighten the grip on the laser holding bar.  There is also a wing nut on the back side so you can adjust the height.

If you cut the hole just right the laser will be a press fit.  If loose a little hot glue will hold it steady.

To make the top bracket Jim took a block of wood and marked where he wanted the holes for the shafts and for the holding bolts and drilled the holes.   Jim also marked the square for the laser shaft.  The slits are cut on a band saw and a band saw was used to square the hole for the laser shaft.

Here you can see how Jim marked the hole to be made square.  

A round hole made square.  

Other ways to make a laser hold.

This one was made of metal using a garden hook with a mounted a gun sight laser on the end.  

This was also made of wood using 3/4" hardwood dowels glued into holes drilled into the mounting blocks.  The laser is fasten to a block held in place by a thumb screw and can be adjusted fore and aft as well as up and down and left and right.  

An alternative is to buy a commercial laser holder on a commercial boring bar such as the one demonstrated by a Lyle Jamerson representative at one of our club meetings.